Lorem ipsum dolor sit amet, consectetuer adipiscing elit. Quisque congue tristique eros. Nulla facilisi. Quisque sem mauris, ullamcorper ac, gravida id, mattis id, sapien. Nullam adipiscing enim dapibus felis. Fusce a nisi in odio pulvinar fringilla. Nunc blandit interdum metus. Duis leo nunc, sollicitudin ut, fermentum congue, pharetra eu, massa. Suspendisse potenti. Morbi commodo mauris. Ut at pede. Ut id nisi. Donec scelerisque urna quis ligula. Praesent est. Vestibulum scelerisque. Curabitur quam. Fusce rhoncus pellentesque ipsum. Aenean venenatis metus ac quam. Maecenas lacus lacus, sagittis vitae, congue at, euismod eu, urna. Maecenas vitae purus. Praesent eros lectus, porta et, semper nec, molestie eget, tortor.
An optically clear, removable, anti-corrosion
adhesive with mould inhibitor built in
Greater UV resistance and color stability - won't yellow with age.
Greater long term durability – the urethane’s
physical properties don't degrade with wear.
The patented acrylic adhesive will withstand lubricants, oils, UV rays, and also contains
an anti-corrosion polymer which inhibits rust and mold growth. This new formulation now allows you to handle the film aggressively without leaving finger prints or
stretch marks in the adhesive – even on black vehicles!
During Nissan & Mercedes testing, the leading competitors’ film was punctured with a 9lb probe; VentureShield was not punctured until 20lb of pressure was applied. Therefore, the film is over 100% more abrasive resistant, meaning no paint damage
Here you will be able to buy our most popular sizes of extra sheets that you can use to template yourself. Easy to cut with a sharp craft knife, and has hundreds of possibilities.
Use it for mountain bikes, car roofs, marine, mobile and PDA covers, iPod video, PSP cover, laptops, etc. Also suitable for home use. Not recommended for delicate items. The possibilities are endless! The film is heat resistant up to 220o
The clear film will not interfere with vinyl or painted graphics and is designed to match the gloss levels of today's automotive factory clearcoat paint systems, providing virtually invisible protection. However, if the Paint Protection Film is removed, damage may occur to the underlying graphic during the removal process.
Silvering is a whitish/silver color that appears under the film and is most noticeable on darker colors. If insufficient squeegee pressure is used during an application, small amounts of air and water mix and form micro bubbles underneath the film. The remedy is to add a little more soap (no more than 2/3 drops) to the water/soap solution to help the squeegee slide more easily while using a firmer application stroke. The extra soap also gives the installer more time before the adhesive tacks to the surface.
Lift lines look similar to silvering and are caused by lifting the film and putting it back down after the adhesive has already set up and tacked. To fix a lift line, lift the film a few inches past the lift line, spray with the alcohol solution and then re-squeegee. To prevent lift lines, add a little more soap to the water/soap solution. This gives the installer more time before the adhesive tacks to the surface.
3M recommends that any repainted surfaces on your vehicle be professionally and fully cured before applying paint protection film. If you have touched up scratches or chips with a tube of "touch-up" paint and then apply paint protection over it, the film will protect that area until it is removed. If the paint protection film is removed, it is possible that the paint around the non-professional touch-up paint could peel off.
There are a number of reasons why film may not stick. Always use proper cleaning and preparation techniques that are standard in the industry. For example,do not use contaminated cleaning towels. Do not get overspray from other processes on the surface to be cleaned. Incorrectly mixed solution can cause low or no tack.
Fingerprints can be avoided during installation by keeping your fingers wet. After the installation is complete, the material must be replaced to correct the issue.
If the bubble is close to the edge, spray soap solution onto the film and squeegee with a fast, firm stroke. If the film is not fully tacked yet (early in the application), the film can be lifted just past the bubble and reapplied using standard application techniques. If the film has tacked, then use a diabetic syringe to fix the bubble.Prepare the diabetic syringe by bending the needle to a 45 degree angle to allow for insertion of the needle at the base of the bubble. If the bubble is filled with solution, insert the needle and extract the solution using the syringe. If the bubble is filled with air, fill the syringe with alcohol solution; insert the needle into the bubble; inject the alcohol solution into the bubble to expand the diameter of the bubble; then extract the alcohol and the air using the syringe.
Yes. Ventureshield paint protection film uses a patented acrylic adhesive which can be safely removed without residue, leaving your bike looking as great as the day you bought it! But remember, the film cannot then be re-used.
No. Ventureshield paint protection film does the job of the tank pad without changing the look of the tank. It is so tough it will stop bag scratches, leather scratches and key and zip damage.
They have been designed for novice fitment specifically for each and every bike, however, some bikes are harder than others. The film is very forgiving and flexible, just follow the instructions supplied and you will have a perfect installation.
The kit may not fit correctly because it may have stretched during installation or have been improperly aligned on the vehicle. Due to the nature of the kit cutting process, there could also be some variation in the size of kits.
Yes. We have our most popular sizes of plain universal sheets available in our online store, these are adequate for most uses, but if you want longer lengths, we can supply you with rolls. If you are fortunate to have a large RV, a trailer, horse box, boat or airplane, this is a more economical option.
If any adhesive remains on the vehicle after removal of the film, it can be removed by using 3M™ General Purpose Adhesive Cleaner (3M Part #08984), according to the package directions.
You sure can! Hundreds of uses some of our customers have entailed are:
Taxi cabs, driving schools, R.V's, trucks, boats, horse boxes, light aircraft (especially gliders), mountain bikes, laptops, PDA's, PSP's, cell phones, etc etc. The film is not recommended for fragile or delicate items
